Reliability, failure probability, and strength of resin-based materials for CAD/CAM restorations

ABSTRACT Objective: This study investigated the Weibull parameters and 5% fracture probability of direct, indirect composites, and CAD/CAM composites. Material and Methods: Discshaped (12 mm diameter x 1 mm thick) specimens were prepared for a direct composite [Z100 (ZO), 3M-ESPE], an indirect laboratory composite [Ceramage (CM), Shofu], and two CAD/CAM composites [Lava Ultimate (LU), 3M ESPE; Vita Enamic (VE), Vita Zahnfabrik] restorations (n=30 for each group). The specimens were polished, stored in distilled water for 24 hours at 37°C. Weibull parameters (m= modulus of Weibull, σ0= characteristic strength) and flexural strength for 5% fracture probability (σ5%) were determined using a piston-on-three-balls device at 1 MPa/s in distilled water. Statistical analysis for biaxial flexural strength analysis were performed either by both one-way ANOVA and Tukey's post hoc (α=0.05) or by Pearson's correlation test. Results: Ranking of m was: VE (19.5), LU (14.5), CM (11.7), and ZO (9.6). Ranking of σ0 (MPa) was: LU (218.1), ZO (210.4), CM (209.0), and VE (126.5). σ5% (MPa) was 177.9 for LU, 163.2 for CM, 154.7 for Z0, and 108.7 for VE. There was no significant difference in the m for ZO, CM, and LU. VE presented the highest m value and significantly higher than ZO. For σ0 and σ5%, ZO, CM, and LU were similar but higher than VE. Conclusion: The strength characteristics of CAD/ CAM composites vary according to their composition and microstructure. VE presented the lowest strength and highest Weibull modulus among the materials.

Symbiotic potential and survival of native rhizobia kept on different carriers

Native rhizobia are ideal for use as commercial legume inoculants. The characteristics of the carrier used to store the inoculants are important for the survival and symbiotic potential of the rhizobia. The objective of this study was to investigate the effects of peat (PEAT), perlite sugarcane bagasse (PSB), carboxymethyl cellulose plus starch (CMCS), and yeast extract mannitol supplemented with mannitol (YEMM) on the survival, nodulation potential and N₂ fixation capacity of the native strains Sinorhizobium mexicanum ITTG R7^T and Rhizobium calliandrae LBP2-1^T and of the reference strain Rhizobium etli CFN42^T. A factorial design (4 × 3) with four repetitions was used to determine the symbiotic potential of the rhizobial strains. The survival of the strains was higher for PEAT (46% for strain LBP2-1^T, 167% for strain CFN42^T and 219% for strain ITTG R7^T) than for the other carriers after 240 days, except for CFN42^T kept on CMCS (225%). All the strains kept on the different carriers effectively nodulated common bean, with the lowest number of nodules found (5 nodules) when CFN42^T was kept on CMCS and with the highest number of nodules found (28 nodules) when ITTG R7^T was kept on PSB. The nitrogenase activity was the highest for ITTG R7^T kept on PEAT (4911 μmol C₂H₄ per fresh weight nodule h⁻¹); however, no activity was found when the strains were kept on YEMM. Thus, the survival and symbiotic potential of the rhizobia depended on the carrier used to store them.

Hospitalización por episodios de cianosis en recién nacidos de edad gestacional igual o mayor a 34 semanas / Hospital Admissions due to cyanosis episodes in newborns with gestational age of 34 weeks or more

Objetivo: Caracterizar la hospitalización por episodios de cianosis en recién nacidos (RN) > 34 semanas. Pacientes y método: Estudio retrospectivo que incluyó la totalidad de los RN hospitalizados por episodios de cianosis entre enero de 2007 y diciembre de 2012. En ellos se aplicaron 2 protocolos de estudio que consideraban exámenes de primera y segunda línea; estos últimos ante la recurrencia de eventos. El protocolo de primera línea consideró exámenes bioquímicos generales, radiografía de tórax y ecocardiografía en casos seleccionados, en tanto que el protocolo de segunda línea incluyó electroencefalograma, electrocardiograma, resonancia magnética nuclear encefálica, screening metabólico ampliado, ácido pirúvico, ácido láctico y en caso de convulsiones, citoquímico y cultivo de líquido cefalorraquídeo y reacción en cadena de la polimerasa para herpes. Resultados: Noventa y ocho de un total de 3.454 (2,8%) RN hospitalizados ingresaron por episodio de cianosis. La edad gestacional (EG) fue 37,8 + 1,36 semanas; peso al nacimiento: 3145 + 477 g. Edad materna: 32 + 4,8 años. El 19,4% de las madres tenía antecedentes mórbidos: diabetes gestacional (8,1%), síndrome hipertensivo del embarazo (5,1%), colestasia intrahepática (3,1%) y retardo del crecimiento (3,1%). Género: 48,8% masculino, parto por cesárea: 68,4%. Edad al ingreso: 1,9 + 1,4 días; duración de la hospitalización: 4,2 + 4,2 días. En todos los pacientes se practicaron exámenes de primera línea y en el 39,8% exámenes de segunda línea. En el 21,4% de los RN se identificó una causa, siendo el síndrome convulsivo el más frecuente (33%). Los RN con diagnóstico asociado presentaron 3,8 + 2,7 episodios de cianosis versus 1,5 + 2,4 en el grupo sin diagnóstico (NS). El 15,4% se fueron de alta con monitor; no hubo reingresos. Conclusión: La incidencia de hospitalización neonatal por episodios de cianosis fue de 6 por 1.000 RN vivos. Solo en cerca de un 20% de ellos es posible identificar una causa, siendo la más frecuente el síndrome convulsivo.

Objectives: A retrospective study was performed between January 2007 and December 2012 to assess the admission rates of newborns due to episodes of cyanosis Patients and method: Retrospective study that included all the newborns hospitalized with episodes of cyanosis between January 2007 and December 2012. In them were employed two study protocols that considered first and second line tests, the latter in view of recurrence of events. The first line protocol considered general biochemical tests, chest x-ray and echocardiography in selected cases, while the second line protocol included electroencephalogram, electrocardiogram, nuclear magnetic resonance of the brain, expanded metabolic screening, pyruvic acid, lactic acid, and in case of seizures, cytochemical, and culture of cerebrospinal fluid (CSF) and PCR (polymerase chain reaction) for herpes. Results: A total of 98 (2.8%) out of 3,454 newborns were admitted due to episodes of cyanosis. Gestational age: 37.8 + 1.4 weeks, birth weight: 3,145 + 477 g. Maternal age: 32 + 4.8 years. Disease was present in 19.4% of mothers; gestational diabetes (8.1%), pregnancy induced hypertension (5.1%), intrahepatic cholestasis (3.1%), and intrauterine growth retardation (3.1%). Gender: 48.8% male, 51.2% female (NS). Birth: caesarean section, 68.4%, and vaginal delivery, 31.6%. Age on admission 1.9 + 1.4 days. Hospital stay: 4.2 + 4.2 days. First line tests were performed in 100% of patients with 39.8% fulfilling the criteria for second line study. A condition was detected in 21.4%, with convulsive syndrome was the most frequent (33%). Newborns with an identified condition had 3.8 + 2.7episodes versus 1.5 + 2,4 in those without diagnosis (NS). A home oxygen monitor was given to 15.4%. There were no re-admissions. Conclusions: Most newborns admitted due to cyanosis are discharged with a condition of unknown origin. In this study, convulsive syndrome was the most frequent cause.

Effect of composite surface treatment and aging on the bond strength between a core build-up composite and a luting agent

Objective The purpose of this study was to assess the influence of conditioning methods and thermocycling on the bond strength between composite core and resin cement. Material and Methods Eighty blocks (8×8×4 mm) were prepared with core build-up composite. The cementation surface was roughened with 120-grit carbide paper and the blocks were thermocycled (5,000 cycles, between 5°C and 55°C, with a 30 s dwell time in each bath). A layer of temporary luting agent was applied. After 24 h, the layer was removed, and the blocks were divided into five groups, according to surface treatment: (NT) No treatment (control); (SP) Grinding with 120-grit carbide paper; (AC) Etching with 37% phosphoric acid; (SC) Sandblasting with 30 mm SiO2 particles, silane application; (AO) Sandblasting with 50 mm Al2O3 particles, silane application. Two composite blocks were cemented to each other (n=8) and sectioned into sticks. Half of the specimens from each block were immediately tested for microtensile bond strength (µTBS), while the other half was subjected to storage for 6 months, thermocycling (12,000 cycles, between 5°C and 55°C, with a dwell time of 30 s in each bath) and µTBS test in a mechanical testing machine. Bond strength data were analyzed by repeated measures two-way ANOVA and Tukey test (α=0.05). Results The µTBS was significantly affected by surface treatment (p=0.007) and thermocycling (p=0.000). Before aging, the SP group presented higher bond strength when compared to NT and AC groups, whereas all the other groups were statistically similar. After aging, all the groups were statistically similar. SP submitted to thermocycling showed lower bond strength than SP without thermocycling. Conclusion Core composites should be roughened with a diamond bur before the luting process. Thermocycling tends to reduce the bond strength between composite and resin cement. .

Effect of Different Surface Treatments for Ceramic Bracket Base on Bond Strength of Rebonded Brackets

The aim of this study was to evaluate the shear bond strength of rebonded ceramic brackets after subjecting the bracket base to different treatments. Seventy-five premolars were selected and randomly distributed into five groups (n=15), according to the type of the bracket surface treatment: I, no treatment, first bonding (control); II, sandblasting with aluminum oxide; III, sandblasting + silane; IV, silica coating + silane; and V, silicatization performed in a laboratory (Rocatec system). The brackets were fixed on an enamel surface with Transbond XT resin without acid etching. The brackets were then removed and their bases were subjected to different treatments. Thereafter, the brackets were fixed again to the enamel surface and the specimens were subjected to shear bond strength (SBS) test. The adhesive remnant index (ARI) was then evaluated for each specimen. Data were subjected to ANOVA and Tukey's tests (α=0.05). A statistically significant difference was observed only between Rocatec and the other groups; the Rocatec group showed the lowest SBS values. The highest SBS values were observed for group 1, without any significant difference from the values for groups II, III and IV. Most groups had a higher percentage of failures at the enamel-resin interface (score 1). It was concluded that the surface treatments of rebonded ceramic brackets were effective, with SBS values similar to that of the control group, except Rocatec group.

O objetivo do estudo foi avaliar o efeito de tratamentos da base de bráquetes cerâmicos monocristalinos na resistência de união ao esmalte após recolagem. Setenta e cinco pré-molares foram selecionados e aleatoriamente distribuídos em 5 grupos (n=15) de acordo com o tratamento da base do bráquete: I - sem tratamento, primeira colagem (controle), II - jateamento com óxido de alumínio, III - jateamento seguido da aplicação de silano, IV - jateamento com partículas de dióxido de sílica (silicatização) seguido de silano, V - silicatização realizada em laboratório (Sistema Rocatec). Os bráquetes foram colados no esmalte com Transbond XT sem condicionamento ácido. Em seguida, os bráquetes foram removidos e suas bases foram submetidas aos diferentes tratamentos. Os bráquetes foram recolados, armazenados por 24 h e submetidos ao ensaio mecânico de cisalhamento com velocidade de 0,5 mm/min. Após, o índice de remanescente adesivo (IRA) foi avaliado em cada espécime. Os dados foram submetidos à análise de variância e teste de Tukey (α=0,05). Pode-se observar que houve diferença significativa apenas entre o sistema Rocatec e os demais grupos, o qual apresentou os menores valores de resistência. Os maiores valores de resistência foram observados para o grupo I (controle), sem diferença significativa dos grupos II, III e IV. A maioria dos grupos apresentou maior porcentagem de falhas na interface esmalte/resina (escore 1). Pode-se concluir que os tratamentos da base do bráquete cerâmico foram efetivos, apresentando valores similares ao grupo controle, exceto para o grupo em que foi usado Rocatec.

Genetic variability in G2 and F2 region between biological clones of human respiratory syncytial virus with or without host immune selection pressure

Human respiratory syncytial virus (HRSV) is an important respiratory pathogens among children between zero-five years old. Host immunity and viral genetic variability are important factors that can make vaccine production difficult. In this work, differences between biological clones of HRSV were detected in clinical samples in the absence and presence of serum collected from children in the convalescent phase of the illness and from their biological mothers. Viral clones were selected by plaque assay in the absence and presence of serum and nucleotide sequences of the G2 and F2 genes of HRSV biological clones were compared. One non-synonymous mutation was found in the F gene (Ile5Asn) in one clone of an HRSV-B sample and one non-synonymous mutation was found in the G gene (Ser291Pro) in four clones of the same HRSV-B sample. Only one of these clones was obtained after treatment with the child's serum. In addition, some synonymous mutations were determined in two clones of the HRSV-A samples. In conclusion, it is possible that minor sequences could be selected by host antibodies contributing to the HRSV evolutionary process, hampering the development of an effective vaccine, since we verify the same codon alteration in absence and presence of human sera in individual clones of BR-85 sample.

Microstructure and Mechanical Properties of Composite Resins Subjected to Accelerated Artificial Aging

The aim of this study was to investigate the influence of accelerated artificial aging (AAA) on the microstructure and mechanical properties of the Filtek Z250, Filtek Supreme, 4 Seasons, Herculite, P60, Tetric Ceram, Charisma and Filtek Z100. composite resins. The composites were characterized by Fourier-transform Infrared spectroscopy (FTIR) and thermal analyses (Differential Scanning Calorimetry - DSC and Thermogravimetry - TG). The microstructure of the materials was examined by scanning electron microscopy. Surface hardness and compressive strength data of the resins were recorded and the mean values were analyzed statistically by ANOVA and Tukey's test (α=0.05). The results showed significant differences among the commercial brands for surface hardness (F=86.74, p<0.0001) and compressive strength (F=40.31, p<0.0001), but AAA did not affect the properties (surface hardness: F=0.39, p=0.53; compressive strength: F=2.82, p=0.09) of any of the composite resins. FTIR, DSC and TG analyses showed that resin polymerization was complete, and there were no differences between the spectra and thermal curve profiles of the materials obtained before and after AAA. TG confirmed the absence of volatile compounds and evidenced good thermal stability up to 200 °C, and similar amounts of residues were found in all resins evaluated before and after AAA. The AAA treatment did not significantly affect resin surface. Therefore, regardless of the resin brand, AAA did not influence the microstructure or the mechanical properties.

A influência do sistema de envelhecimento artificial acelerado (EAA) na microestrutura e nas propriedades mecânicas das resinas compostas Z250, Filtek Supreme, 4 Seasons, Herculite, P60, Tetric Ceram, Charisma e Filtek Z100 foi investigada. Os compósitos foram caracterizados por espectroscopia de infravermelho com transformada de Fourier (FTIR) e análises térmicas (calorimetria exploratória diferencial - DSC e termogravimetria - TG). A microestrutura dos materiais foi analisada por microscopia eletrônica de varredura. Os dados de dureza superficial e resistência à compressão foram registados para as resinas e os valores médios foram submetidos ao teste de Kolmogorov-Smirnov (p>0,05), ANOVA e teste de Tukey (α=0,05). Os resultados mostraram diferenças significativas entre as marcas comerciais em termos de dureza (F=86,74, p<0,0001) e resistência à compressão (F=40,31, p<0,0001), mas o EAA não afetou as propriedades (dureza superficial: F=0,39, p=0,53, resistência à compressão: F=2,82, p=0,09) de qualquer uma das resinas. FTIR, DSC e análise de TG revelou que a polimerização da resina foi completa, e não houve diferenças entre os espectros e os perfis de curva térmica dos materiais obtidos, antes e depois de EAA. TG mostrou a ausência de compostos voláteis e evidenciou uma boa estabilidade térmica até 200 °C, e quantidades similares de resíduos foram encontradas em todas as resinas avaliadas, antes e depois de EAA. O tratamento de EAA não afetou significativamente a superfície das resinas. Portanto, independentemente do tipo de resina, o EAA não influenciou a microestrutura e as propriedades mecânicas.

Surface morphology changes of acrylic resins during finishing and polishing phases

INTRODUCTION: The finishing and polishing phases are essential to improve smoothness and shining on the surface of acrylic resins used to make removable orthodontic appliances. A good surface finishing reduces roughness, which facilitates hygiene, prevents staining and provides greater comfort to the patients. OBJECTIVE: The aim of this paper was to analyze the changes on surface morphology of acrylic resins during finishing and polishing phases. METHODS: Thirty discs (10 mm in diameter and 5 mm in length) were made with acrylic resin and randomly divided into ten groups. The control group did not receive any treatment while the other groups received gradual finishing and polishing. The last group received the entire finishing and polishing procedures. Surface morphology was qualitatively analyzed through scanning electron microscopy and quantitatively analyzed through a laser profilometer test. RESULTS: The acrylic resin surfaces without treatment showed bubbles which were not observed in the subsequent phases. Wearing out with multilaminated burs, finishing with wood sandpaper and finishing with water sandpaper resulted in surfaces with decreasing irregularities. The surfaces that were polished with pumice and with low abrasive liquids showed high superficial smoothness. CONCLUSION: Highly smooth acrylic resin surfaces can be obtained after mechanical finishing and polishing performed with multilaminated burs, wood sandpaper, water sandpaper, pumice and low abrasive liquids.

INTRODUÇÃO: as etapas de acabamento e polimento são essenciais para a obtenção de lisura e brilho da superfície de resinas acrílicas utilizadas na confecção de aparelhos ortodônticos. O bom acabamento da resina facilita a higiene, previne o manchamento e propicia maior conforto ao paciente. OBJETIVO: o objetivo desse trabalho foi analisar as alterações na morfologia superficial de resinas acrílicas (Clássico, São Paulo) durante as etapas do acabamento e polimento mecânico. MÉTODOS: foram confeccionados 30 discos (10mm de diâmetro e 5mm de altura) de resina acrílica autopolimerizável, que foram divididos aleatoriamente em dez grupos. O grupo controle não recebeu nenhum tratamento. Os demais grupos receberam acabamento e polimento graduais. O último grupo recebeu todo o tratamento de acabamento e polimento. A morfologia superficial foi avaliada qualitativamente por microscopia eletrônica de varredura e quantitativamente pela análise da rugosidade superficial. RESULTADOS: as superfícies de resina acrílica sem tratamento apresentaram bolhas, as quais não foram observadas nas fases subsequentes. O desgaste com fresa multilaminada seguido de acabamento com lixa de madeira e lixa d'água produziram superfícies com irregularidades decrescentes. As superfícies polidas com branco de Espanha e líquido de baixa abrasividade (Kaol) apresentaram bom acabamento superficial. CONCLUSÃO: é possível obter resina acrílica com alta lisura superficial após acabamento e polimento mecânico com fresas, lixas de madeira, lixas d'água, branco de Espanha e líquidos de baixa abrasividade (Kaol).

Effect of silica coating and silane surface treatment on the bond strength of soft denture liner to denture base material

OBJECTIVE: This study investigated the effects of different surface treatments on the tensile bond strength of an autopolymerizing silicone denture liner to a denture base material after thermocycling. MATERIAL AND METHODS: Fifty rectangular heat-polymerized acrylic resin (QC-20) specimens consisting of a set of 2 acrylic blocks were used in the tensile test. Specimens were divided into 5 test groups (n=10) according to the bonding surface treatment as follows: Group A, adhesive treatment (Ufi Gel P adhesive) (control); Group S, sandblasting using 50-µm Al2O3; Group SCSIL, silica coating using 30-µm Al2O3 modified by silica and silanized with silane agent (CoJet System); Group SCA, silica coating and adhesive application; Group SCSILA, silica coating, silane and adhesive treatment. The 2 PMMA blocks were placed into molds and the soft lining materials (Ufi Gel P) were packed into the space and polymerized. All specimens were thermocycled (5,000 cycles) before the tensile test. Bond strength data were analyzed using 1-way ANOVA and Duncan tests. Fracture surfaces were observed by scanning electron microscopy. X-ray photoelectron spectrometer (XPS) and Fourier Transform Infrared spectrometer (FTIR) analysis were used for the chemical analysis and a profilometer was used for the roughness of the sample surfaces. RESULTS: The highest bond strength test value was observed for Group A (1.35±0.13); the lowest value was for Group S (0.28±0.07) and Group SCSIL (0.34±0.03). Mixed and cohesive type failures were seen in Group A, SCA and SCSILA. Group ...

Heat treatment following surface silanization in rebonded tribochemical silica-coated ceramic brackets: shear bond strength analysis

OBJECTIVE: This study aimed to evaluate the effects of heat treatment on the tribochemical silica coating and silane surface conditioning and the bond strength of rebonded alumina monocrystalline brackets. MATERIAL AND METHODS: Sixty alumina monocrystalline brackets were randomly divided according to adhesive base surface treatments (n=20): Gc, no treatment (control); Gt, tribochemical silica coating + silane application; Gh, as per Gt + post-heat treatment (air flux at 100ºC for 60 s). Brackets were bonded to the enamel premolars surface with a light-polymerized resin and stored in distilled water at 37ºC for 100 days. Additionally, half the specimens of each group were thermocycled (6,000 cycles between 5-55ºC) (TC). The specimens were submitted to the shear bond strength (SBS) test using a universal testing machine (1 mm/min). Failure mode was assessed using optical and scanning electron microscopy (SEM), together with the surface roughness (Ra) of the resin cement in the bracket using interference microscopy (IM). 2-way ANOVA and the Tukey test were used to compare the data (p>0.05). RESULTS: The strategies used to treat the bracket surface had an effect on the SBS results (p=0.0), but thermocycling did not (p=0.6974). Considering the SBS results (MPa), Gh-TC and Gc showed the highest values (27.59±6.4 and 27.18±2.9) and Gt-TC showed the lowest (8.45±6.7). For the Ra parameter, ANOVA revealed that the aging method had an effect (p=0.0157) but the surface treatments did not (p=0.458). For the thermocycled and non-thermocycled groups, Ra (µm) was 0.69±0.16 and 1.12±0.52, respectively. The most frequent failure mode exhibited was mixed failure involving the enamel-resin-bracket interfaces. CONCLUSION: Regardless of the aging method, Gh promoted similar SBS results to Gc, suggesting that rebonded ceramic brackets are ...

Effect of Carbamide Peroxide Bleaching Gel on Composite Resin Flexural Strength and Microhardness

This study investigated the effect of 16% carbamide peroxide (Whiteness Perfect/FGM) on the Vickers microhardness and flexural strength of the restorative composites Filtek Z100 (hybrid), Filtek Z350 (nanofill), Brilliant (micro-hybrid) and Opallis (micro-hybrid). Disc-shaped (4x2 mm; n=5) and bar-shaped (12x2x1 mm; n=10) specimens of each restorative material were randomly divided into 2 groups: (G1) 16 weeks stored in distilled water; (G2) 16 weeks stored in distilled water, with 16% carbamide peroxide application during 6 h per day for the last 4 weeks. The mechanical properties were evaluated using a Vickers microhardness tester and a mechanical testing machine. Data were analyzed by two-way ANOVA and Tukey's (HSD) post-hoc test (α=0.05). Filtek Z100 presented the highest microhardness value, followed by Filtek Z350 and finally by Brilliant and Opallis (p=0.00). Filtek Z100 and Brilliant exhibited the highest flexural strength value, followed by Filtek Z350 and Opallis (p=0.00). Bleaching treatment decreased significantly microhardness of Brilliant and Opallis (p=0.00). The flexural strength of all studied materials was not affected by the home bleaching (p=0.28).

Este estudo investigou o efeito do peróxido de carbamida a 16% (Whiteness Perfect/FGM) na dureza Vickers e resistência à flexão dos compósitos restauradores Filtek Z100 (híbrida), Filtek Z350 (nanoparticulada), Brilliant (micro-híbrida) e Opallis (micro-híbrida). Espécimes em forma de disco (4x2 mm; n=5) e de barra (12x2x1 mm; n=10) de cada material restaurador foram distribuídos aleatoriamente em 2 grupos: (G1) 16 semanas em água destilada; (G2) armazenamento em água destilada durante 16 semanas, com aplicação do peróxido de carbamida a 16% por 6 h diárias nas últimas 4 semanas. As propriedades mecânicas foram avaliadas em microdurômetro Vickers e máquina de ensaios mecânicos. Os dados foram analisados por ANOVA a 2 critérios e teste de Tukey (α=0,05). Filtek Z100 apresentou o maior valor de dureza, seguido por Filtek Z350 e, finalmente, por Brilliant e Opallis (p=0,00). Filtek Z100 e Brilliant mostraram o maior valor de resistência à flexão, seguido por Filtek Z350 e Opallis (p=0,00). O clareamento diminuiu significantemente a dureza das resinas Brilliant e Opallis (p=0,00). A resistência à flexão dos materiais estudados não foi afetada pelo clareamento caseiro (p=0,28).

Castor oil polyurethane containing silica nanoparticles as filling material of bone defect in rats / Poliuretana de mamona contendo nanopartículas de sílica como material de preenchimento de defeito ósseo em ratos

PURPOSE: To evaluate the biologic behavior of the castor polymer containing silica nanoparticles as a bone substitute in diafisary defect. METHODS: Twenty seven male rattus norvegicus albinus wistar lineage were submitted to bone defect filled with castor oil polymer. Three experimental groups had been formed with nine animals each: (1) castor oil polymer containing only calcium carbonate; (2) castor oil polymer with calcium carbonate and doped with 5 percent of silica nanoparticles; (3) castor polymer with calcium carbonate doped with 10 percent of silica nanoparticles; 3 animals of each group were submitted to euthanasia 15, 30 and 60 days after experimental procedure, and their femurs were removed to histological evaluation. RESULTS: there was bone growth in all the studied groups, with a greater tendency of growth in the group 1. After 30 days all the groups presented similar results. After 60 days a greater amount of fibroblasts, osteoblasts, osteocytes and osteoclasts in group 3 was observed, with integrated activity of 3 kinds of cells involved in the bone activation-reabsorption-formation. CONCLUSIONS: The castor polymer associated to the silica nanoparticles is biocompatible and allows osteoconduction. The presence of osteoprogenitors cells suggests silica osteoinduction capacity.

OBJETIVO: Avaliar o comportamento biológico do polímero de mamona contendo nanopartículas de sílica como substituto ósseo. MÉTODOS: Vinte e sete rattus norvergicus albinus, Wistar foram submetidos a defeito ósseo preenchido com polímero de mamona. Foram formados três grupos experimentais, com nove ratos cada: (1) Polímero com carbonato de cálcio; (2) Polímero com carbonato de cálcio dopado com 5 por cento de nanopartículas de sílica; (3) Polímero com carbonato de cálcio dopado com 10 por cento de nanopartículas de sílica; três animais de cada grupo foram submetidos à eutanásia 15, 30 e 60 dias após o procedimento experimental e os fêmures removidos e submetidos à avaliação histológica. RESULTADOS: Houve crescimento ósseo em todos os grupos estudados, com maior tendência de crescimento no grupo contendo polímero de mamona acrescido apenas por carbonato de cálcio. Aos 30 dias, todos os grupos apresentaram resultados semelhantes. Aos 60 dias, notou-se maior presença de fibroblastos, osteoblastos, osteócitos e osteoclastos no grupo 3, com persistência da atividade integrada dos três tipos de células envolvidas no processo de ativação-reabsorção-formação óssea. CONCLUSÕES: O polímero de mamona associado com nanopartículas de sílica é biocompatível e permite a osteocondução. A presença de células osteoprogenitoras nos implantes contendo 10 por cento de sílica indica sua capacidade osteoindutora.

Silicosis Caused by Chronic Inhalation of Snail Shell Powder

A 70-yr-old woman visited our hospital for shortness of breath. Chest CT showed ground glass opacity and traction bronchiectasis at right middle, lower lobe and left lingular division. Video-assisted thoracic surgical biopsy at right lower lobe and pathologic examination revealed mixed dust pneumoconiosis. Polarized optical microscopy showed lung lesions were consisted of silica and carbon materials. She was a housewife and never been exposed to silica dusts occupationally. She has taken freshwater snails as a health-promoting food for 40 yr and ground shell powder was piled up on her backyard where she spent day-time. Energy dispersive X-ray spectroscopy of snail shell and scanning electron microscopy with energy dispersive x-ray spectroscopy of lung lesion revealed that silica occupies important portion. Herein, we report the first known case of silicosis due to chronic inhalation of shell powder of freshwater snail.

Repair of amalgam restorations with composite resin and bonded amalgam: A microleakage study.

Background: Total replacement is the most common technique for defective amalgam restorations, and it represents a major part of restorative dental treatment. Repair is an alternative option for amalgam restorations with localized defects. Aims: This study compared microleakage of amalgam restorations repaired by bonded amalgam or composite resin. Materials and Methods: Thirty extracted human pre-molars were prepared and restored with class I amalgam. A simulated defect was prepared that included the cavosurface margin on restorations, and the pre-molars were assigned to two treatment groups (n=15): In group 1, premolars were treated by composite resin (34% Tooth Conditioner Gel + Adper Single Bond 2 + Z100) and in group 2, premolars were repaired by bonded amalgam (34% Tooth Conditioner Gel + Prime and Bond 2.1 + Permite C). The teeth were immersed in a 50% silver nitrate solution, thermocycled, sectioned longitudinally and then observed by three examiners using a stereomicroscope. Microleakage was evaluated using a 0-4 scale for dye penetration, and data was analyzed by Kruskal Wallis and Dunn tests. Results: Neither of the two methods eliminated microleakage completely. Composite resin was significantly the most effective for repair/tooth interface sealing (score 0 = 80.0%; P=0.0317). For the repair/restoration interface, composite resin was also statistically more effective as a sealant (score 0=66%; P=0.0005) when compared to the bonded amalgam technique (score 0=13%; P=0.0005). Conclusions: The use of adhesive systems significantly affected the ability to seal the repair/ tooth interface. However, at the level of the repair/restoration interface, the bonded amalgam technique may increase microleakage.

Effects of silica coating and silane surface conditioning on the bond strength of rebonded metal and ceramic brackets

OBJECTIVE: The aim of this study was to evaluate the effects of tribochemical silica coating and silane surface conditioning on the bond strength of rebonded metal and ceramic brackets. MATERIAL AND METHODS: Twenty debonded metal and 20 debonded ceramic brackets were randomly assigned to receive one of the following surface treatments (n=10 for each group): (1) sandblasting (control); (2) tribochemical silica coating combined with silane. Brackets were rebonded to the enamel surface on the labial and lingual sides of premolars with a light-polymerized resin composite. All specimens were stored in distilled water for 1 week and then thermocycled (5,000 cycles) between 5-55ºC. Shear bond strength values were measured using a universal testing machine. Student's t-test was used to compare the data (α=0.05). Failure mode was assessed using a stereomicroscope, and the treated and non-treated bracket surfaces were observed by scanning electron microscopy. RESULTS: Rebonded ceramic brackets treated with silica coating followed by silanization had significantly greater bond strength values (17.7±4.4 MPa) than the sandblasting group (2.4±0.8 MPa, P<0.001). No significant difference was observed between the rebonded metal brackets treated with silica coating with silanization (15±3.9 MPa) and the sandblasted brackets (13.6±3.9 MPa). Treated rebonded ceramic specimens primarily exhibited cohesive failure in resin and adhesive failure at the enamel-adhesive interface. CONCLUSIONS: In comparison to sandblasting, silica coating with aluminum trioxide particles followed by silanization resulted in higher bond strengths of rebonded ceramic brackets.

In vitro dentin permeability after application of Gluma® desensitizer as aqueous solution or aqueous fumed silica dispersion

OBJECTIVES: To assess and to compare the effects of Gluma® Desensitizer (GDL) with an experimental glutaraldehyde and HEMA containing fumed silica dispersion (GDG) on dentin permeability using a chemiluminous tracer penetration test. MATERIAL AND METHODS: Twenty disc-shaped dentin specimens were dissected from extracted human third molars. The dentin specimens were mounted in a split chamber device for determination of permeability under liquid pressure using a photochemical method. Ten specimens were randomly selected and allocated to the evaluation groups Gluma® Desensitizer as aqueous solution and glutaraldehyde/HEMA as fumed silica dispersion, respectively. Dentin disc permeability was determined at two pressure levels after removal of smear with EDTA, after albumin soaking, and after application of the desensitizing agents. Two desensitizer-treated and rinsed specimens of each group were examined by scanning electron microscopy (SEM) for surface remnants. RESULTS: Comparatively large standard deviations of the mean EDTA reference and albumin soaked samples permeability values refected the differences of the dentin substrates. The mean chemiluminescence values of specimen treated with GDL and GDG, respectively, were signifcantly reduced after topical application of the desensitizing agents on albumin-soaked dentin. The effects of GDL and GDG on permeability were not signifcantly different. Treated specimens showed no surface remnants after rinsing. CONCLUSIONS: The experimental desensitizer gel formulation reduced dentin permeability as effectively as the original Gluma® Desensitizer solution.

Comparative in vitro study of the shear bond strength of brackets bonded with restorative and orthodontic resins

The aim of this study was to evaluate the shear bond strength of brackets bonded with different restorative systems and compare it with that afforded by an established orthodontic bonding system. Seventy human bicuspids were used, divided into five different groups with 14 teeth each. Whereas a specific orthodontic bonding resin (TransbondTM XT) was used in the control group, the restorative systems Charisma, Tetric Ceram, TPH Spectrum and Z100 were used in the other four groups. Seven days after bonding the brackets to the samples, shear forces were applied under pressure in a universal testing machine. The data collected was evaluated using the ANOVA test and, when a difference was identified, the Tukey test was applied. A 5 percent level of significance was adopted. The mean results of the shear bond strength tests were as follows: Group 1 (Charisma), 14.98 MPa; Group 2 (Tetric Ceram), 15.16 MPa; Group 3 (TPH), 17.70 MPa; Group 4 (Z100), 13.91 MPa; and Group 5 or control group (TransbondTM XT), 17.15 MPa. No statistically significant difference was found among the groups. It was concluded that all tested resins have sufficient bond strength to be recommended for bonding orthodontic brackets.

Effect of prepolymerized composite megafiller on the marginal adaptation of composite restorations in cavities with different C-factors: An SEM study.

Aim: To evaluate the effect of prepolymerized custom-made composite megafiller and configuration factors (C-factor) on marginal adaptation of resin composite restorations. Materials and Methods: Forty extracted human mandibular molars were divided into four experimental groups consisting of 10 samples each. In groups I and III, class V (configuration factor 5) and in groups II and IV, class II box-shaped cavities (configuration factor 2) were prepared. Groups I and II were restored with a nanofilled composite (Filtek™ Z350 3M ESPE, St Paul, MN, USA) placed in horizontal increments. In groups III and IV, preformed composite megafiller was placed and cavities were restored with nanofilled composite Z-350. After curing, the samples were finished and prepared for examination under low vacuum scanning electron microscope. The data were analyzed with one-way analysis of variance. The significance between the individual groups was calculated by Post hoc test using the Holm-Sidak method ( P≤0.05). Results: The marginal gap values in groups III and IV were significantly lower than in groups I and II, respectively ( P≤0.05). Minimum gap values were seen in group IV. Conclusion: Use of prepolymerized composite megafiller and a lower C-factor decreased the marginal gaps between the tooth and composite restorations.

Effect of filler particles on surface roughness of experimental composite series

OBJECTIVE: The purpose of this study was to evaluate the effect of different filler sizes and shapes on the surface roughness of experimental resin-composite series. MATERIAL AND METHODS: Thirty-three disc-shaped specimens of the series (Spherical-RZD 102, 105, 106, 107, 114 and Irregular-RZD 103, 108, 109, 110, 111, 112) were prepared in a split Teflon mold and irradiated with an halogen light-curing unit (450 mW/cm² for 40 s) at both top and bottom surfaces. The specimens were stored for 3 months in distilled water. The surface roughness values in form of surface finish-vertical parameter (Ra), maximum roughness depth (Rmax) and horizontal roughness parameter (Sm) were recorded using a contact profilometer. The data were analyzed by one-way ANOVA and the means were compared by Scheffé post-hoc test (a=0.05). RESULTS: The lowest surface roughness (Ra) was observed in S-100 (0.079±0.013), while the roughest surface was noted in I-450/700/1000 (0.125±0.011) and I-450/1000 (0.124±0.004). The spherical-shape series showed the smoothest surface finish compared to the irregular-shape ones with higher significant difference (p>0.05). The vertical surface roughness parameter (Ra) values increased as the filler size increased yielding a linear relation (r²=0.82). On the contrary, the horizontal parameter (Sm) was not significantly affected by the filler size (r²=0.24) as well as the filler shape. CONCLUSIONS: Filler particle's size and shape have a great effect on the surface roughness parameters of these composite series.